Icom 7600

Icom 7600

HF Transceiver

IC-7600 Specifications

General

Frequency coverage
RX: 0.03 – 60.000 MHz *1, *2
TX:
1.800 – 1.999 MHz
3.500 – 3.999 MHz
5.3305, 5.3465, 5.3665, 5.3715, 5.4035 MHz
7.000 – 7.300 MHz
10.100 – 10.150 MHz *2
14.000 – 14.350 MHz *2
18.068 – 18.168 MHz *2
21.000 – 21.450 MHz *2
24.890 – 24.990 MHz *2
28.000 – 29.700 MHz *2
50.000 – 54.000 MHz *2
*1=some freq. bands are not guaranteed. *2=Depending on version
Mode: USB, LSB, CW, RTTY, PSK31, AM, FM
Number of memory channels: 101 (99 regular, 2 scan edges)
Antenna connector: SO-239×2 and phono [RCA;(50 ohms)]
Usable temperature range: 0°C to +50°C; +32°F to +122°F
Frequency stability: less than ±0.5 ppm (1 minute after power ON/0°C to +50°C; +32°F to +122°F)
Frequency resolution: 1Hz
Power supply requirement: 13.8 V DC (±15% negative ground)
Power consumption:
TX max power 23A
RX standby 3.0A (typ.)
RX max audio 3.5A (typ.)
Dimensions (projections not included): 340(W) x 116(H) x 280(D) mm; 13.37(W) x 4.5(H) x 11.2(D) inches
Weight: 10 kg; 25 lb.
ACC 1 connector: 8-pin DIN connector
ACC 2 connector: 7-pin DIN connector
CI-V connector: 2-conductor 3.5 (d) mm (1/8″)
Display: 5.8 inch (diagonal) TFT color LCD

Transceiver
Output power (continually adjustable):
SSB/CW/RTTY/PSK31/FM: 2 – 100 Watts
AM: 1 – 30 Watts
Modulation system:
SSB: PSN modulation
AM: Low power modulation
FM: Phase modulation
Spurious emissions: -50 dB (HF bands), -60 dB (50 MHz band)
Carrier suppression: 40 dB
Unwanted sideband suppression: 55 dB
delta TX variable range: ±9.999 kHz
Microphone connector: 8-pin connector (600 ohms)
ELE-KEY connector: 3-conductor 6.35 (d) mm (1/4″)
KEY connector: 3-conductor 6.35 (d) mm (1/4″)
SEND connector: Phono (RCA)
ALC connector: Phono (RCA)


Receiver

Receive system: Double conversion superheterodyne
Intermediate frequencies:
1st: 64.455 MHz
2nd: 455 kHz
Squelch sensitivity (Pre-amp ON):
SSB: Less than 3.2 µV
FM: Less than 0.3 µV
Selectivity (representative value, filter shape at SHARP):
SSB (BW: 2.4 kHz): More than 2.4 kHz/-6 dB, Less than 2.8 kHz/-60 dB
CW (BW: 500 Hz): More than 500 Hz/-6 dB, Less than 700 Hz/-60 dB
RTTY (BW: 350 Hz): More than 350 Hz/-6 dB, Less than 650 Hz/-60 dB
AM (BW: 6 kHz): More than 6.0 kHz/-6 dB, Less than 15.0 kHz/-60 dB
FM (BW: 15 kHz): More than 12.0 kHz/-6 dB, Less than 20.0 kHz/-60 dB
Spurious and image rejection ratio: More than 70 dB (except IF through on 50 MHz band)
AF output power (at 13.8 V DC): More than 2.0 W at 10% distortion with an 8 ohm load
RIT variable range: ±9.999 kHz
PHONES connector: 2-pin connector 6.35 (d) mm (1/4″)
EXT SP connector: 2-pin connector 3.5 (d) mm (1/4″)/8 ohms


Antenna Tuner

Matching impedance range:
16.7 – 150 ohms unbalanced *1 (HF bands)
20 – 125 ohms unbalanced *2 (50 MHz band)
*1=Less than VSWR 3:1; *2=Less than VSWR 2.5:1
Minimum operating input power: 8 Watts
Tuning accuracy: VSWR 1.5:1 or less
Insertion loss: Less than 1.0 dB(after tuning)
Specifications are preliminary are subject to change without notice or obligation.

 

You can leave a response, or trackback from your own site.

Leave a Reply


five × 9 =